Hendor improves the powder coating pre-treatment process
We as Hendor constantly strive for innovation in the pumps and filters for the surface finishing industry. Therefore, we critically look for improvements in our products and its applications. This time we found a way to optimize the chemical pre-treatment of powder coating process.
During the powder coating pre-treatment process the chemicals in the spray tunnel are often contaminated and not of constant quality, even with a frequent feed and bleed regime.
How did we optimize the powder coating pre-treatment process?
We developed a filter technology that keeps the quality of the degreasing fluid constant and clean. The filter remains active longer and captures significantly more dirt due to an adsorption filtration system. This technology combines physical separation and adsorption mechanisms successfully. In the end, this results in a continuously cleansed degreasing bath, containing 70% less dirt in the process solution.
Benefits of the adsorption filtration system for the powder coater:
- 90% reduction in adhesion problems
- Less chemical addition for the degreasing bath
- Less solution replacement
- Less maintenance for the powder coating pre-treatment plant
- Nozzles are less likely to clog
- Filter medium is easy to replace
- Reduced waste water volumes
- Higher productivity
- Less rework
What is powder coating pre-treatment?
Powder coating pre-treatment is a chemical process which prepares a surface to be effectively powder coated. The process entails chemical treatment to take off all dirt and oxides. As a next step, a chemical treatment is given to create an intermediate conversion coating to enhance corrosion resistance and adhesion. Besides pre-treatment in a spray tunnel, also dip pre-treatment is commonly used in the surface finishing industry.
Benefits of powder coating pre-treatment:
- Reduces rejection rate
- Increases corrosion resistance
- Enhances adhesion
- Maximizes product life time
Products which can be used for the powder coating pre-treatment process:
This is why you should use vertical pumps for scrubber applications
It still is pretty common to see horizontal pumps being used in scrubber applications. Hendor believes that vertical sealless immersion, dry run safe...
How selecting the right filter media reduces your TCO
Choosing the right filter media will lower your Total Cost of Ownership (TCO). We provide the right solution with our wide range of filter media.
Hendor Excellence filter experience
Noch eine Woche, dann ist es so weit. Hendor bringt seine neue Serie von HE-Filtern für die Oberflächenbehandlungsindustrie auf den Markt. E...
Wie sich die Investition in den neuen HE-Filter rentiert
Die Anschaffung von neuen Pumpen und Filtern ist immer mit einer Investition verbunden. Für Maschinenbauer und Endanwender in der Oberfläche...
Vorteile der HE-Filter für die Oberflächenindustrie
Die neuen Hendor HE-Filter sind die erste umweltfreundliche Alternative zu Pumpen und Filtern für die Oberflächenindustrie. Mit Blick auf di...
Die Zukunft ist grün
Wir können den Klimawandel nicht länger ignorieren. Wie jeder andere Industriezweig trägt auch die Oberflächenbehandlungsindustrie...
Hendor und Pforzheimer OTSM schließen Partnerschaft für Service und Unterstützung der höchste Stufe
Beide Unternehmen werden das Know-how des jeweils anderen nutzen, um Innovationen für die Zukunft zu entwickeln.
Best suitable pumps and filters for Reel-to-Reel plating applications
Hendor was the first to set the standard for vertical pumps in Reel-to-Reel plating lines, helping Reel-to-Reel line operators and OEM’s with best i...
Pumps and filters for best performance aluminium anodizing equipment
Hendor provides several pump and filter solutions for aluminium anodizing. Read our recommendations and their benefits for your anodizing equipment.
Underrated in surface finishing: preventive maintenance
Preventive maintenance is crucial for chemical pumps and filters. It prevents unexpected downtime and complete breakdown. Hendor explains the process.
Beneficial for electroless nickel applications: D16 SS
Latest fabrication technologies ensure that the Hendor D16 stainless steel vertical pump range is sealless, dry-run safe, and maintenance free.
This is why you should inspect your centrifugal pumps weekly
Centrifugal pumps & chemical filtration systems should be inspected weekly. Here, you find the correct way to perform the centrifugal pump inspection.
Latest trends in the surface finishing industry identified
September has been special for society as well as the industry. Governments have been lifting restrictions on physical meetings and events.
Hendor celebrates 73 years of craftsmanship
It is our 73th anniversary in the surface finishing industry. We have gathered a lot of knowledge and experience about our products & customers.
Our part in the green industry: electric motors
As from Juli 2021, new European energy standards apply for electric motors. Hendor took measures to do its part in innovating for future generations.
It's always a pleasure doing business with Hendor
The first trimester of 2021 has proven to be just as eventful as 2020. Therefore, our business director reflects on his first four months at Hendor.
Maintenance-free pumps for powder coating spray tunnels
Whenever you are building a powder coating plant, you have two options when it comes to the spray tunnel pumps: a horizontal- or vertical pump.
Hendor HRC: stop expensive precious metal loss
Companies are continuously looking for cost saving measures in their plating shops. Hendor offers a solution with the Hendor Recovery Cell (HRC).
Hendor is ahead of new EU electric motor regulations
Hendor decided to transition its 0,12 .. 0,55 kW electric motors directly to IE3, surpassing the legal minimum of IE2.
Our manufacturing process explained: Assembly & Testing
How do our pumps & filters go from PP to an end product? Step 5: assembly and testing.
Our manufacturing process explained: wet paint coating
How do our pumps & filters arise from PP to an end product? Step 4: wet paint coating the electric motor.
Our manufacturing process explained: plastic welding
How do our pumps & filters arise from PP to an end product? Step 3: plastic welding.
Our manufacturing process explained: mechanical machining
How do our pumps & filters arise from polypropylene (PP) to an end product? Step 2: mechanical machining.
From polypropylene to Hendor end product
How do our pumps & filters arise from polypropylene (PP) to an end product? Step 1: injection molding.
Kees Stigter joins Hendor as our new Sales Director
We welcome a new member to the Hendor team: Kees Stigter. He takes the role of Sales Director, and will be responsible for our global product sales.
The Hendor standard: safe & easy installation and maintenance
When you buy new chemical pumps, you have to take into account the piping. We deliver all our pumps with pre-fabricated three-piece unions.
Hendor DM-series: best of both worlds
Due to the frequent use of different precious metal finishes from various electrolytes, a standard centrifugal pump is not always appropriate.
Hendor celebrates 25 years of presence in North America
This year marks the 25th anniversary of Hendor-PE Inc.. We proudly look back at the way our partners have carried out the Hendor legacy overseas.
Hendor customization: this is how we do it
With decades of experience in designing pumps and filters, our engineering department creates customized specialties tailored to your demands.
D13: less energy, more power
Sustainability means a long product lifetime, but also the reduction of emission. We redeveloped our D110 series and replaced it with our D13 series.
Hendor SHX: stainless steel is the new thermoplastic
The market is in need of pumps and filters which are capable of high performance. Therefore, we developed the SHX series, made out of stainless steel.
Hendor improves the powder coating pre-treatment process
We developed filter technology that keeps the quality of the degreasing fluid constant & clean. The filter remains active longer & captures more dirt.
Hendor presents new robust Basket Strainer
In order to protect both magnetic drive and mechanical seal pumps, we want to introduce our new basket strainer.