Underrated in surface finishing: preventive maintenance
Preventive maintenance (PM) is one of the most underrated aspects of upkeeping chemical pumps and filters. Often, less attention is paid to smaller signs or they are only noticed when it is already too late. As a result, consequential damage is likely larger than needed, causing unplanned production downtime and significantly higher cost of repair.
Contact Hendor for assistance with your chemical pumps or filters.
Benefits of preventive maintenancePreventive maintenance is the process of inspecting and servicing chemical pumps or filters before particular parts are worn out. It prevents unexpected downtime and complete breakdown. It is the follow-up of weekly inspection, where technicians look, hear and feel for deviations when equipment is running.
During the preventive maintenance process, qualified engineers inspect wear, and measure bearing tolerances. Similar to weekly inspection, this process should be done periodically. Based on these regular measurements, the amount of wear over a specific period of time can be calculated and therefore predict the moment of replacement. Hendor advices to schedule preventive maintenance every 6 to 12 months.
The process of preventive maintenance requires scheduling and provides the following benefits:
- Increasing the longevity and reliability of your pump or filter;
- Preventing consequential damage;
- Preventing unplanned production downtime, as a result of unexpected pump or filter breakdown;
- Providing more insight in the actual use of your pumps or filters in your application.
Preventive maintenance entails several steps. Hendor visualized this process in the following video.
Preventive maintenance explained
- Disconnect power supply or switch to maintenance in the electrical cabinet;
- Close all valves;
- Release air- and drain valves and drain the filter;
- Disconnect union suction nut and discharge;
- Unscrew smart pump pull-back system star knob;
- Disconnect the power supply cable, and take the pump to the workbench to dismount;
- Examine the level of wear and inspect the bearing tolerances. Find replacement thresholds in the Hendor manuals;
- Reassemble all dismantled parts.
In case you need assistance, technical experts at the Hendor service department can help you with any request or question. Contact them via mail or the dedicated request form.
Wie sich die Investition in den neuen HE-Filter rentiert
Die Anschaffung von neuen Pumpen und Filtern ist immer mit einer Investition verbunden. Für Maschinenbauer und Endanwender in der Oberfläche...
Vorteile der HE-Filter für die Oberflächenindustrie
Die neuen Hendor HE-Filter sind die erste umweltfreundliche Alternative zu Pumpen und Filtern für die Oberflächenindustrie. Mit Blick auf di...
Die Zukunft ist grün
Wir können den Klimawandel nicht länger ignorieren. Wie jeder andere Industriezweig trägt auch die Oberflächenbehandlungsindustrie...
Hendor und Pforzheimer OTSM schließen Partnerschaft für Service und Unterstützung der höchste Stufe
Beide Unternehmen werden das Know-how des jeweils anderen nutzen, um Innovationen für die Zukunft zu entwickeln.
Best suitable pumps and filters for Reel-to-Reel plating applications
Hendor was the first to set the standard for vertical pumps in Reel-to-Reel plating lines, helping Reel-to-Reel line operators and OEM’s with best i...
Pumps and filters for best performance aluminium anodizing equipment
Hendor provides several pump and filter solutions for aluminium anodizing. Read our recommendations and their benefits for your anodizing equipment.
Underrated in surface finishing: preventive maintenance
Preventive maintenance is crucial for chemical pumps and filters. It prevents unexpected downtime and complete breakdown. Hendor explains the process.
Beneficial for electroless nickel applications: D16 SS
Latest fabrication technologies ensure that the Hendor D16 stainless steel vertical pump range is sealless, dry-run safe, and maintenance free.
This is why you should inspect your centrifugal pumps weekly
Centrifugal pumps & chemical filtration systems should be inspected weekly. Here, you find the correct way to perform the centrifugal pump inspection.
Latest trends in the surface finishing industry identified
September has been special for society as well as the industry. Governments have been lifting restrictions on physical meetings and events.
Hendor celebrates 73 years of craftsmanship
It is our 73th anniversary in the surface finishing industry. We have gathered a lot of knowledge and experience about our products & customers.
Our part in the green industry: electric motors
As from Juli 2021, new European energy standards apply for electric motors. Hendor took measures to do its part in innovating for future generations.
It's always a pleasure doing business with Hendor
The first trimester of 2021 has proven to be just as eventful as 2020. Therefore, our business director reflects on his first four months at Hendor.
How selecting the right filter media reduces the TCO
Choosing the right filter media will lower your Total Cost of Ownership (TCO). We provide the right solution with our wide range of filter media.
Maintenance-free pumps for powder coating spray tunnels
Whenever you are building a powder coating plant, you have two options when it comes to the spray tunnel pumps: a horizontal- or vertical pump.
Hendor HRC: stop expensive precious metal loss
Companies are continuously looking for cost saving measures in their plating shops. Hendor offers a solution with the Hendor Recovery Cell (HRC).
Hendor is ahead of new EU electric motor regulations
Hendor decided to transition its 0,12 .. 0,55 kW electric motors directly to IE3, surpassing the legal minimum of IE2.
Our manufacturing process explained: Assembly & Testing
How do our pumps & filters go from PP to an end product? Step 5: assembly and testing.
Our manufacturing process explained: wet paint coating
How do our pumps & filters arise from PP to an end product? Step 4: wet paint coating the electric motor.
Our manufacturing process explained: plastic welding
How do our pumps & filters arise from PP to an end product? Step 3: plastic welding.
Our manufacturing process explained: mechanical machining
How do our pumps & filters arise from polypropylene (PP) to an end product? Step 2: mechanical machining.
From polypropylene to Hendor end product
How do our pumps & filters arise from polypropylene (PP) to an end product? Step 1: injection molding.
Kees Stigter joins Hendor as our new Sales Director
We welcome a new member to the Hendor team: Kees Stigter. He takes the role of Sales Director, and will be responsible for our global product sales.
The Hendor standard: safe & easy installation and maintenance
When you buy new chemical pumps, you have to take into account the piping. We deliver all our pumps with pre-fabricated three-piece unions.
Hendor DM-series: best of both worlds
Due to the frequent use of different precious metal finishes from various electrolytes, a standard centrifugal pump is not always appropriate.
Hendor celebrates 25 years of presence in North America
This year marks the 25th anniversary of Hendor-PE Inc.. We proudly look back at the way our partners have carried out the Hendor legacy overseas.
Hendor customization: this is how we do it
With decades of experience in designing pumps and filters, our engineering department creates customized specialties tailored to your demands.
D13: less energy, more power
Sustainability means a long product lifetime, but also the reduction of emission. We redeveloped our D110 series and replaced it with our D13 series.
Hendor SHX: stainless steel is the new thermoplastic
The market is in need of pumps and filters which are capable of high performance. Therefore, we developed the SHX series, made out of stainless steel.
Hendor improves the powder coating pre-treatment process
We developed filter technology that keeps the quality of the degreasing fluid constant & clean. The filter remains active longer & captures more dirt.
Hendor presents new robust Basket Strainer
In order to protect both magnetic drive and mechanical seal pumps, we want to introduce our new basket strainer.