Hendor presents new robust Basket Strainer
We as Hendor see a lot of advantages of using our vertical pump systems. Due to technical innovations like a free turning shaft, no pump bearing, and minor seals, this pump system is very reliable and maintenance free. But, sometimes installing a vertical pump system isn’t possible. A lack of tank space, close installed flight bars, and accessibility, are a couple of reasons not to choose for a vertical pump. A horizontal pump could be the solution, but what if you deal with contaminated liquids? Large particles in the liquid can cause major pump problems. Fast wearing of pump bearings and mechanical seals, clogging of the pump, and early failure, are some examples of common problems.
Basket strainer protects magnetic drive and mechanical seal pumps
In order to protect both magnetic drive and mechanical seal pumps, we want to introduce our new basket strainer. By using a fine mesh the pump is protected to particles of 3 mm and larger. Beside this standard mesh the strainer can also be equipped with a fully capsuled neodymium magnet which catch magnetic particles like steel and certain stainless steels. This results in a significant improvement of the lifetime of the pump, less pump maintenance and a way higher uptime of the installation.
Our new and robust basket strainer features:
- Fully injection moulded glass reinforced PP
- Including complete +GF+ union ends
- Screw cap cover including air release valve
- Removable easy to clean basket with 3 mm width perforation
The Hendor basket strainer comes in 2 sizes:
- Small, with 3,5 liter volume and DN50 connection
- Large, with 7,0 liter volume and DN90 connection
This is why you should use vertical pumps for scrubber applications
It still is pretty common to see horizontal pumps being used in scrubber applications. Hendor believes that vertical sealless immersion, dry run safe...
How selecting the right filter media reduces your TCO
Choosing the right filter media will lower your Total Cost of Ownership (TCO). We provide the right solution with our wide range of filter media.
Hendor Excellence filter experience
Nog een week en dan is het zover. Hendor lanceert haar nieuwe serie HE-filters voor de oppervlaktebehandelende industrie. Het is de eerste lichting va...
Zo verdient u de investering in de nieuwe HE-filter terug
De aanschaf van nieuwe pompen en filters vraagt altijd om een investering. Voor machinebouwers en eindgebruikers binnen de oppervlaktebehandelende ind...
Voordelen van de HE-filters voor de oppervlaktebehandelende industrie
De nieuwe Hendor HE-filters zijn het eerste groene alternatief voor pompen en filters voor de oppervlaktebehandelende industrie. Met de groeiende impa...
De toekomst is groen
Klimaatverandering kan niet langer worden genegeerd. Net als elke andere industrie is het een effect waarvoor de oppervlaktebehandelende industrie ver...
Hendor partners up with Pforzheimer OTSM for next level service & support
Both companies will share each others’ expertise in order to innovate for the future.
Best suitable pumps and filters for Reel-to-Reel plating applications
Hendor was the first to set the standard for vertical pumps in Reel-to-Reel plating lines, helping Reel-to-Reel line operators and OEM’s with best i...
Pumps and filters for best performance aluminium anodizing equipment
Hendor provides several pump and filter solutions for aluminium anodizing. Read our recommendations and their benefits for your anodizing equipment.
Underrated in surface finishing: preventive maintenance
Preventive maintenance is crucial for chemical pumps and filters. It prevents unexpected downtime and complete breakdown. Hendor explains the process.
Beneficial for electroless nickel applications: D16 SS
Latest fabrication technologies ensure that the Hendor D16 stainless steel vertical pump range is sealless, dry-run safe, and maintenance free.
This is why you should inspect your centrifugal pumps weekly
Centrifugal pumps & chemical filtration systems should be inspected weekly. Here, you find the correct way to perform the centrifugal pump inspection.
Latest trends in the surface finishing industry identified
September has been special for society as well as the industry. Governments have been lifting restrictions on physical meetings and events.
Hendor celebrates 73 years of craftsmanship
It is our 73th anniversary in the surface finishing industry. We have gathered a lot of knowledge and experience about our products & customers.
Our part in the green industry: electric motors
As from Juli 2021, new European energy standards apply for electric motors. Hendor took measures to do its part in innovating for future generations.
It's always a pleasure doing business with Hendor
The first trimester of 2021 has proven to be just as eventful as 2020. Therefore, our business director reflects on his first four months at Hendor.
Maintenance-free pumps for powder coating spray tunnels
Whenever you are building a powder coating plant, you have two options when it comes to the spray tunnel pumps: a horizontal- or vertical pump.
Hendor HRC: stop expensive precious metal loss
Companies are continuously looking for cost saving measures in their plating shops. Hendor offers a solution with the Hendor Recovery Cell (HRC).
Hendor is ahead of new EU electric motor regulations
Hendor decided to transition its 0,12 .. 0,55 kW electric motors directly to IE3, surpassing the legal minimum of IE2.
Our manufacturing process explained: Assembly & Testing
How do our pumps & filters go from PP to an end product? Step 5: assembly and testing.
Our manufacturing process explained: wet paint coating
How do our pumps & filters arise from PP to an end product? Step 4: wet paint coating the electric motor.
Our manufacturing process explained: plastic welding
How do our pumps & filters arise from PP to an end product? Step 3: plastic welding.
Our manufacturing process explained: mechanical machining
How do our pumps & filters arise from polypropylene (PP) to an end product? Step 2: mechanical machining.
From polypropylene to Hendor end product
How do our pumps & filters arise from polypropylene (PP) to an end product? Step 1: injection molding.
Kees Stigter joins Hendor as our new Sales Director
We welcome a new member to the Hendor team: Kees Stigter. He takes the role of Sales Director, and will be responsible for our global product sales.
The Hendor standard: safe & easy installation and maintenance
When you buy new chemical pumps, you have to take into account the piping. We deliver all our pumps with pre-fabricated three-piece unions.
Hendor DM-series: best of both worlds
Due to the frequent use of different precious metal finishes from various electrolytes, a standard centrifugal pump is not always appropriate.
Hendor celebrates 25 years of presence in North America
This year marks the 25th anniversary of Hendor-PE Inc.. We proudly look back at the way our partners have carried out the Hendor legacy overseas.
Hendor customization: this is how we do it
With decades of experience in designing pumps and filters, our engineering department creates customized specialties tailored to your demands.
D13: less energy, more power
Sustainability means a long product lifetime, but also the reduction of emission. We redeveloped our D110 series and replaced it with our D13 series.
Hendor SHX: stainless steel is the new thermoplastic
The market is in need of pumps and filters which are capable of high performance. Therefore, we developed the SHX series, made out of stainless steel.
Hendor improves the powder coating pre-treatment process
We developed filter technology that keeps the quality of the degreasing fluid constant & clean. The filter remains active longer & captures more dirt.
Hendor presents new robust Basket Strainer
In order to protect both magnetic drive and mechanical seal pumps, we want to introduce our new basket strainer.